C8051T610DB24【PDF 94/218 页】DAUGHTER BOARD T610 24QFN SOCKET

您好，
买卖IC网欢迎您。
请登录
免费注册

90页 91页 92页 93页 [94页]95页 96页 97页 98页

C8051T610/1/2/3/4/5/6/7

17. EPROM Memory

Electrically programmable read-only memory (EPROM) is included on-chip for program code storage. The

EPROM memory can be programmed via the C2 debug and programming interface when a special pro-

gramming voltage is applied to the V PP pin. Each location in EPROM memory is programmable only once

(i.e., non-erasable). Table 7.6 on page 34 shows the EPROM specifications.

17.1. Programming and Reading the EPROM Memory

Reading and writing the EPROM memory is accomplished through the C2 programming and debug inter-

face. When creating hardware to program the EPROM, it is necessary to follow the programming steps

listed below. Refer to the “C2 Interface Specification” available at http://www.silabs.com for details on com-

municating via the C2 interface. Section “27. C2 Interface” on page 208 has information about C2 register

addresses for the C8051T610/1/2/3/4/5/6/7.

17.1.1. EPROM Write Procedure

1. Reset the device using the RST pin.

2. Wait at least 20 μs before sending the first C2 command.

3. Place the device in core reset: Write 0x04 to the DEVCTL register.

4. Set the device to program mode (1st step): Write 0x40 to the EPCTL register.

5. Set the device to program mode (2nd step): Write 0x4A to the EPCTL register.

Note: Prior to date code 1119, 0x58 should be written to EPCTL.

6. Apply the VPP programming Voltage.

7. Write the first EPROM address for programming to EPADDRH and EPADDRL.

8. Write a data byte to EPDAT. EPADDRH:L will increment by 1 after this write.

9. Use a C2 Address Read command to poll for write completion.

10.(Optional) Check the ERROR bit in register EPSTAT and abort the programming operation if necessary.

11. If programming is not finished, return to Step 8 to write the next address in sequence, or return to

Step 7 to program a new address.

12.Remove the VPP programming Voltage.

13.Remove program mode (1st step): Write 0x40 to the EPCTL register.

14.Remove program mode (2nd step): Write 0x00 to the EPCTL register.

15.Reset the device: Write 0x02 and then 0x00 to the DEVCTL register.

Important Note : There is a finite amount of time which V PP can be applied without damaging the device,

which is cumulative over the life of the device. Refer to Table 7.1 on page 31 for the V PP timing specifica-

tion.

94

Rev 1.1

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

*

*

相关PDF资料

C8051T630DB20 BOARD SOCKET DAUGHTER 20-QFN

CAN-100 BOARD EVAL RS232 100QFP

CANADAPT28 KIT ADAPTER CANDEMOBOARD 28PLCC

CAT24AA01WI-GT3 IC EEPROM SERIAL 1KB I2C 8SOIC

CAT24AA02WI-G IC EEPROM SERIAL 2KB I2C 8SOIC

CAT24C01ZI-G IC EEPROM SERIAL 1KB I2C 8MSOP

CAT24C03WI-G IC EEPROM SERIAL 2KB I2C 8SOIC

CAT24C04ZI-G IC EEPROM SERIAL 4KB I2C 8MSOP

相关代理商/技术参数

C8051T610DB28 功能描述:子卡和OEM板 C8051T610 Family Socket Daughtr Board RoHS:否制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit

C8051T610DB32 功能描述:子卡和OEM板 C8051T610 Family Socket Daughtr Board RoHS:否制造商:BeagleBoard by CircuitCo 产品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit

C8051T610DK 功能描述:开发板和工具包 - 8051 C8051T610 Series Development Kit RoHS:否制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:

C8051T610-GQ 功能描述:8位微控制器 -MCU 16KB 10ADC 32Pin MCU RoHS:否制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT

C8051T610-GQR 功能描述:8位微控制器 -MCU 16KB 10ADC 32Pin MCU RoHS:否制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT

C8051T611-GM 功能描述:8位微控制器 -MCU 16KB 10ADC 28Pin MCU RoHS:否制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT

C8051T611-GMR 功能描述:8位微控制器 -MCU 16KB 10ADC 28Pin MCU RoHS:否制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT

C8051T612-GQ 功能描述:8位微控制器 -MCU 8KB 10ADC 32Pin MCU RoHS:否制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT